Sika® Primer MB
2-component epoxy primer and moisture barrier.
Sika® Primer MB is a 2-component epoxy primer and moisture barrier for SikaBond wood flooring adhesives applied on difficult substrates.
- 2-Component
- Reactive epoxy
- Solvent-free
- Easy to apply, low viscosity
- Allows quick completion
- Good penetration and stabilization of the substrate
- Suitable for refurbishing existing substrates
- Suitable for use with underfloor heating
Usage
Sika® Primer MB is designed for use in conjunction with SikaBond wood flooring adhesives:- For moisture control on cement-based substrates with moisture contents of up to 6 % CM.
- For substrate consolidation on concrete, cement and anhydrite screeds and refurbished substrates.
- For adhesion promotion for broadcast mastic asphalt and on old adhesive residues.
Advantages
- 2-Component
- Reactive epoxy
- Solvent-free
- Easy to apply, low viscosity
- Allows quick completion
- Good penetration and stabilization of the substrate
- Suitable for refurbishing existing substrates
- Suitable for use with underfloor heating
Packaging
Component A | 7.5 kg metal pail |
Component B | 2.5 kg metal pail |
Component A+B | 10.0 kg metal pail |
Colour
Blue
Product Details
Chemical Base
2-Component, epoxy resin compound
Shelf Life
Sika® Primer MB has a shelf life of 24 months from the date of production, if stored properly in undamaged, original, sealed packaging, and if the storage conditions are met.
Storage Conditions
Sika® Primer MB shall be stored in dry conditions, protected from direct sunlight and at temperatures between +5 °C and +25 °C.
Density
Component A | ~1.10 kg/l |
Component B | ~1.00 kg/l |
Mixed | ~1.10 kg/l |
Shore A Hardness
~80 (after 7 d) | (ISO 868) |
Compressive Strength
~70 N/mm2 (after 7 d) | (EN 196 part 1) |
Thermal Resistance
Sika® Primer MB can be permanently exposed to dry heat ≤ +50 °C and temporarily exposed to dry heat ≤ +80 °C.
Note: In order to avoid damage to the installed wood floor elements, surface temperature must not exceed +25 °C.
Service Temperature
−40 °C min. / +70 °C max.
Application
Mixing Ratio
Component A : Component B = 100:37 (by volume)
Ambient Air Temperature
+10 °C min. / +30 °C max., min. 3 °C above dew point temperature
Relative Air Humidity
< 80 %
Substrate Temperature
During laying and until Sika® Primer MB has fully cured, the substrate and ambient temperatures shall be between +10 °C and +30 °C without and between +20 °C and +30 °C with underfloor heating.
Substrate Moisture Content
Permissible substrate moisture content without underfloor heating
For cement screeds | <6 % CM |
For anhydrite screeds | <0.5 % CM |
For magnetite flooring | 3–12 % CM (depending on the organic content) |
Permissible substrate moisture content for use with underfloor heating
For cement screeds | <6 % CM |
For anhydrite screeds | <0.3 % |
For magnetite flooring | 3–12 % CM (depending on the organic content) |
To check the moisture content, use the “Rubber Mat Test”, according to ASTM. A polyethylene sheet of > 1x1 m in dimension shall be taped to the concrete surface. Leave the polyethylene sheet in place for > 24 hours prior to testing. This test allows for the detection of any condensed vapour transmissions.
Note: CM: carbid method, to determine the moisture content of the substrate. For all moisture contents, the quality of the substrates and surfaces, always follow the guidelines of the wood flooring manufacturer.
Pot Life
Ambient air temperature | Pot life |
+10 °C | ~60 min |
+20 °C | ~30 min |
+30 °C | ~15 min |
Note: Do not use mixed material after pot life.
Curing Time
Conditions | Curing time |
+10 °C | ~18 h |
+20 °C | ~12 h |
+30 °C | ~6 h |
Note: Curing speed is dependent on temperature, relative humidity and absorption of substrates. High temperature and low r.h. decrease curing time. Cured material becomes transparent.
Consumption
Concrete and/or cement screeds and anhydrite screeds, including flowable anhydrite screeds | 400–600 g/m2, depending on the absorbency of the substrate. |
Broadcast mastic asphalt | 250–300 g/m2 |
APPLICATION INSTRUCTIONS
For the application of Sika® Primer MB all generally accepted rules for wood flooring installation apply.
SUBSTRATE PREPARATION
- The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Paint, cement laitance and other poorly adhering contaminants must be removed.
- At least 50 % of the surface area must be cleared of residual adhesive (i.e. by grinding).
- Preliminary bond strength testing is recommended.
- Compressive strength: > 8 N/mm2
- Tensile Bond strength: > 0.8 N/mm2
- Concrete and/or cement screeds must be ground and thoroughly cleaned with an industrial vacuum.
- Anhydrite screeds, including flowable anhydrite screeds must be ground and thoroughly cleaned with an industrial vacuum shortly before coating.
- Broadcast mastic asphalt must be broadcasted to excess and thoroughly cleaned with an industrial vacuum.
- On fiber reinforced concrete any exposed fibers must be burnt off the surface.
- The guidelines of the screed floor manufacturer apply.
- For project specific advice, please contact Sika technical service for assistance.
MIXING
Add component B to component A in the correct ratio using an electric stirrer at a low speed (300–400 rpm).
A minimum mixing time of 3 minutes is required; stirring shall continue until the mix becomes homogeneous. Pour mixed material into a clean container and mix again.
CLEANING OF TOOLS
Clean all tools and application equipment immediately after use with water. Once cured, residual material can only be removed mechanically.