Sikafloor®-266 CR
Sikafloor®-266 CR is a two part, low-emission, self-smoothing, textured and roller coating epoxy resin system designed for cleanrooms. "Total solid epoxy composition according to the test method Deutsche Bauchemie e.V. (German Association for construction chemicals)".
- Very low VOC / AMC emission
- Very low particle emissions
- Organo phosphate and phthalate free
- Good chemical and mechanical resistance
- Easy to clean
- Economical
- Liquid proof
- Gloss finish
- Slip resistant surface possible
Usage
- Especially designed for the use in cleanroom environment, where low VOC/AMC and particle emissions are mandatory.
- Also suitable as a hard wearing course for many industries, such as automotive, pharmaceutical, storage facilities and warehouses.
Advantages
- Very low VOC / AMC emission
- Very low particle emissions
- Organo phosphate and phthalate free
- Good chemical and mechanical resistance
- Easy to clean
- Economical
- Liquid proof
- Gloss finish
- Slip resistant surface possible
Packaging
Part A | 20 kg containers |
Part B | 5 kg containers |
Part A+B | 25 kg ready to mix units |
Colour
Resin - part A | coloured, liquid |
Hardener - part B | transparent, liquid |
Almost unlimited choice of colour shades.
Product Details
ENVIRONMENTAL INFORMATION
- Conformity with LEED v4 MRc 2 (Option 1): Building Product Disclosure and Optimization – Environmental Product Declarations
- Conformity with LEED v4 MRc 4 (Option 2): Building Product Disclosure and Optimization - Material Ingredients
- Conformity with LEED v2009 IEQc 4.2: Low-Emitting Materials - Paints and Coatings
APPROVALS / STANDARDS
- Particle emission certificate Sikafloor-266 CR CSM Statement of Qualification - ISO 14644-1, class 3 - Report No. SI 0706-406 and GMP class A, Report No. SI1008-533.
- Outgassing emission certificate Sikafloor-266 CR: CSM Statement of Qualification - ISO 14644-8, class -7.8 - Report No. SI 0706-406.
- Very good biological Resistance in accordance with ISO 846, CSM Report No. SI 1008-533
- Particle and Outgassing Datasheet Sikafloor-266 CR (90°C) - M+W Zander Holding AG.
- Cetec Emission Study of Sikafloor-266 CR (Project CV060813) in accordance with United States Environmental Protection Agency (USEPA).
- Fire classification in accordance with EN 13501-1, Report-No. 2007-B-1784/1, MPA Dresden, Germany, May 2007.
- Eurofins Emission tested according to the AgBB-scheme and guidelines of the DiBt (AgBB – Committee for Health-related Evaluation of Building Products, DiBt – German Institute for Building Technology). Sampling, testing and evaluation were performed according to ISO-16000, Report No. 763695B.
- Synthetic resin screed material according to EN 13813:2002, Declaration of Performance 02 08 01 02 045 0 000001 1008, certified by notified factory production control certification body 0921, certificate of conformity of the factory production control 2017, and provided with the CE marking.
- Coating for surface protection of concrete according to EN 1504-2:2004, Declaration of Performance 02 08 01 02 045 0 000001 1008, certified by notified factory production control certification body 0921, certificate of conformity of the factory production control 2017, and provided with the CE marking.
Chemical Base
Epoxy
Shelf Life
24 months from date of production.
Storage Conditions
The packaging must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5 °C and +30 °C.
Density
Part A | ~ 1.6 kg/l |
Part B | ~ 1.02 kg/l |
Mixed resin | ~ 1.45 kg/l |
Filled resin 1 : 0,4 | ~ 1.66 kg/l |
All Density values at +23 °C
Solid content by weight
~100 %
Solid content by volume
~100 %
Shore D Hardness
~84 (14 days / +23°C) | (DIN 53 505) |
Abrasion Resistance
45 mg (CS 10/1000/1000) (14 days / +23 °C) | (EN ISO 5470-1 Taber Abraser Test) |
Values have been determined using quartz sand F 34 (0.1-0.3 mm) from Quarzwerke GmbH Frechen sand.
Compressive Strength
~77 N/mm2 (Resin filled 1:0.3 with F34*, 28 days / +23 °C) | (EN 13892-2) |
Tensile Strength in Flexure
~41 N/mm2 (Resin filled 1:0.3 with F34*, 28 days / +23°C) | (EN 13892-2) |
Tensile Adhesion Strength
> 1.5 N/mm² (failure in concrete) | (ISO 4624) |
Chemical Resistance
Resistant to many chemicals. Contact Sika technical service for specific information.
Thermal Resistance
Exposure* | Dry heat |
Permanent | +50 °C |
Short-term max. 7 d | +80 °C |
Short-term max. 16 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Application
Mixing Ratio
Part A : part B = 80 : 20 (by weight)
Ambient Air Temperature
+15 °C min. / +30 °C max.
Relative Air Humidity
80 % r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+15 °C min. / +30 °C max.
Substrate Moisture Content
<4 % pbw moisture content.
Test method: Sika®-Tramex meter, CM-measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperature | Time |
+15 °C | ~ 45 minutes |
+20 °C | ~ 30 minutes |
+30 °C | ~ 15 minutes |
Curing Time
Before overcoating Sikafloor®-266 CR allow:
Substrate temperature | Minimum | Maximum |
+15 °C | 24 hours | 4 days |
+20 °C | 12 hours | 2 days |
+30 °C | 6 hours | 1 day |
Consumption
~0.4–0.6 kg/m² applied as a roller coating
~1.8–2.0 kg/m² applied as a self-smoothing wearing course
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc. For detailed information, please refer to the System data sheet Sikafloor® MultiDur ES-24 EQ.
MIXING
Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved. When parts A and B have been mixed, add the quartz sand 0.1 - 0.3 mm and mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment.
Mixing Tools
Sikafloor®-266 CR must be thoroughly mixed using a low speed electric stirrer (300 - 400 rpm) or other suitable equipment.
APPLICATION
Prior to application, confirm substrate moisture content, relative air humidity and dew point.
If > 4 % pbw moisture content, Sikafloor® EpoCem® may be applied as a Temporary moisture barrier (T.M.B.) system.
Levelling
Rough surfaces need to be levelled first. Therefore use Sikafloor®-144 / -156 / -161 levelling mortar (see product data sheet).
Roller coating
Sikafloor®-266 CR as coating can be applied by short-piled roller (crosswise).
Textured coating
Sikafloor®-266 CR is applied with a serrated trowel and then back-rolled (crosswise) with a textured roller.
Wearing course smooth
Sikafloor®-266 CR is poured, spread evenly by means of a serrated trowel.
After spreading the material evenly, turn the serrated trowel and smooth the surface in order to achieve an aesthetically higher grade of finish.
Roll immediately (within max. 10 minutes of application) in two directions with a spiked roller to ensure even thickness and to remove entrapped air. To obtain the highest level of aesthetic finish, spike roll in two directions at a 90 degree angle, passing only once in each direction.
CLEANING OF TOOLS
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.